10. Linefeed
If the apparatus is rotated by hand with the receiver rail position for line feed, then so
the line feed should be activated correctly.
Before changing the line feed setting, check the following first: Paper handling
(see above), working position of the printer trap (page 18).

a.) Rear stop position 187/63
Press down the actuating catch 175 until the pawl 188 rests against the stop 187. The Role of the Rast•
lever 966 should then be in its lowest position in a tooth gap (rest position).
Adjustment by moving the stop 187.

b.)Position of the front stop 189/64
Slowly push the actuating latch 175/63 down from its rest position until the pawl 188/64
just touches the tooth of the ratchet wheel 965 (ratchet wheel in detent position). Between stop 189
and back of the pawl 188 should then be 1.1 ± 0.1 mm of air at the narrowest point.
Adjustment by moving the stop 189.

c.)Connecting rod length 1799/63
Press down the actuating catch 175 until the pawl 188 rests against the stop 187. Between the
Head of the first screw located on the underside of the operating latch on the side of the connection•
bar, and the upper roller rail 562 should then be at a distance of 1.3 ± 0.2 mm.
Adjustment by adjusting the length of the connecting rod 1799 after loosening the screws 1809.

d.)Spring tension on the pawl 188/65: Turn the platen roller until the locking lever rolls 966/63
stands on a tooth head. Actuating case 175 depress something so that between pawl
188/65 and the tooth in front of it is low air. Approximately 110g to lift the latch
at the designated place.
Adjustment by turning bolt 476

e.)Position of the clamping piece 161/66
20
The position of the sprag on the axle 150 and the position of the axle are determined by
Holes in the axle into which the fastening screws engage.

f.)Axial position of the latching bracket 195/67
Between the lobes of the latching bracket and the feed cam 967 should be in the axial
direction 0.6 ± 0.2mm air. The bracket should be slightly between the adjusting rings 165,
because of can.
Adjustment using the adjusting rings 165.

g.)Working position of the roller 968/178
Push the carriage to the beginning of the line, trigger the printer, turn the drive until the printer latches
stands in front. Press switch rod 969/69 by hand against the nose of the feed lever 970, see above
that it is detected as the drive rotates further. Actuation trap 175/63 before reaching
the rest position of the printer latch by hand so that the pawl 188 on the
beat 187 lies. When the printer trap reaches its resting position, the roller 968/178
place it lightly on the actuation latch that is being held down.
. Adjustment on screw 158 hath loosening screw 156.
More about this source text

h.)Position of the clamping piece 164/68
When the printer is at rest after the line feed has been activated (position as under g) should
between the rear of the shift rod 969/69 and the inner surface of the latching bracket 195
1.5 ± 0.1 mm clearance at the narrowest point. In addition, the latching bracket should move without friction
relative to the pull rod 972 of the clamping piece 971/68 when the spring 973 is released,
was hanged.
Adjustment by turning the clamping piece 164.

i.)Position of the shift rod 969/66
Receipt •Set selector bars for the combination linefeed and manual drive
rotate slowly until the printer latch is in its forward most position. The shift rod 969 is
then pulled against the feed lever 970/69. If, while slowly turning the on,
latch bar 195 begins to recede (movement must be recognizable), the nose of the front,
thrust lever 970 against the lower end of the shift rod. In addition, in the rest,
position of the shift linkage between the upper edge of the actuating latch 175/63 and the roller
968/178 recognizable air. A specific dimension for this distance is not prescribed.
Adjustment on screw 160.